Case 580 injection pump timing

Make sure you use grease NOT oil on the pump seals, the trick to those seals is getting the lip started twisting and slowly but gently pushing. My case 580C backhoe just started to stop running when load is applied. Replaced injector pump, need help timing. Is the injector pump timing the only timing that can be done on that machine? To remedy this, turn engine until timing marks in pump line up.

Turn the crankshaft 3degrees, one full revolution, back to the marks you just. Save case 5injector pump to get e-mail. Bought for a machine and it was not used. Case fuel injection pump. The timing pin is below injection pump.

Two different timing pins were used. One is a plastic insert in the timing housing that slides in and out. The second and later one is a smaller timing housing and a cap that is removable and a steel pin that techs have that goes in the housing. Your pump will come back timed and locked. Next - remove timing window cover from the injection pump and check to see if marks are in alignment.

If they are aligned your done. If not aligned loosen pump mounting nuts. The pump should have the timing lines aligned with each other and then just match the shaft to the pump and install it. Coleman Equipment offers genuine OEM parts online or in one of our Kansas City Area stores - in stock and ready to go. Fuel injection pump gear must not be allowed to move from its position when fuel injection pump is removed from timing gear case.

Do not turn engine over or allow timing gear to move in any way when fuel injection pump is removed. Running only at or about idle speed. I know this thread is ol but boy would I like to know more about fixing my 580C injection pump for a $100.

The cam and injection pump timing is not har at the crank you mesh the one dot with the two dots on the other gear. The engine repair manual is sold separately. Trying to fix a 5that has stood for At least years, owner took off the injector pump and sent away for repair.

Prices are subject to change without notice. Fuel Injection Pump , rebuilt - exchange (core $470). Slowly rotate the fuel injection pump shaft. Install the pump onto the fuel injection pump gear and bolt pump to the timing gear case. There should be two seals on the drive shaft, one to keep the Diesel in the pump and one to keep the oil in the engine.

This table must be used to maintain proper fuel injection pump -to-engine timing. The Control Parts List (CPL) number from the engine dataplate and the. CASE 5Super E Loader Backhoe Service Manual. Once it completely goes away, the motor will over run itself and can lead to major issues at high rpm. Then remove the timing pin access plug from the injection pump and verify if the slot in the pin will fit over the timing tooth of the pump.

Next, carefully replace the pump to correct the timing , adjusting and readjusting the timing pin and access plug in the injection pump. Pictures shown are representational only and do not necessarily reflect the actual part you will receive. How you might implement one emerging trend in organizational design?

I hear Clairton works in. The first step in the repair process is to obtain an injector pump rebuild kit. This usually includes a filter, spacer, pintle cap, and o-rings.

Find a large quantity of carburetor cleaner and bucket as well. The 5Super N offers intuitive fingertip controls for the loader and backhoe pilot configurations, including a joystick FNR rocker, self-leveling, return-to-dig, auxiliary hydraulics and more. Remove the injector pump from the fuel line. Pilot controls and armrests can be repositioned for custom comfort and classic foot-swing CASE controls with mechanical levers are also available. Thanks For Your Business!

With a more powerful engine and at nearly 1inches wide, the 110-hp 5Super N Wide Track takes our most popular backhoe loader to a whole new level. Fortunately there is another method called “spill cut off point timing ” which we can use to time the injection pump. The procedure described below is for the cylinder 23C engine as fitted to the Massey Ferguson 3 but the general process is the same for any engine. Typical example Put fuel injection pump (12) in position on the engine. Ensure that the timing gear is aligned with the hub of fuel injection pump (12).

We sell a wide range of new aftermarket, used and rebuilt 580K replacement parts to get your machine back up and running quickly. Head drive gear is under the two bolt cover on the pump side. PISTONS AND CYLINDER SLEEVES Inspection 1. Timing Gear Cover, Gear and Water Pump.

Using a micrometer, measure the diameter of the piston across the th. Can you tell me which injection pump you have on your 580K. It could use a robert bosch or a C. Let me know I will help you.

One thing you need to know, with a cav pump the engine will not have much torque rise in power. This is a full throttle tractor that should run that way all time. If you are trying to back up hill. This manual is the same used by professional technicians and is a complete reference for overhauling and mechanical servicing of the engine according to the manufacturer’s standards.

Available in downloadable PDF format which can be viewed.